SECAM
From open-encyclopedia.com - the free encyclopedia.
SECAM (Séquentiel Couleur avec Mémoire, French for "sequential color with memory") is an analog color television system first used in France. SECAM has been invented by a team lead by Henri de France and working at Thomson. It is historically the first European color television standard.
| Contents |
Technical details
Just as the other color standards adopted for broadcast usage over the world, SECAM is a compatible standard, which means that monochrome television receivers predating its introduction are still able to correctly show the programs, although only in black and white. Because of this compatibility requirement, color standards add a second signal to the basic monochrome signal, and this signal carries the color information, called chrominance or C in short, while the black and white information is called the luminance (Y in short). Old TV receivers only see the luminance, while color receivers process both signals.
Another aspect of the compatibility being not using more bandwidth than the monochrome signal alone, the color signal has to be somehow inserted into the monochrome signal, without disturbing it. This insertion is possible because the spectrum of the monochrome TV signal is not continuous, hence empty space exists, which can be recycled. This lack of continuity results from the discrete nature of the signal, which is divided into frames and lines. Analog color systems differ by the way in which empty space is used. In all cases, the color signal is inserted at the end of the spectrum of the monochrome signal.
In order to be able to separate
the color signal from the monochrome
one in the receiver, a fixed
frequency subcarrier
has to be used, this subcarrier being
modulated by the color signal.
The color space is three dimensional by the nature of the human vision, so after subtracting the luminance, which is carried by the base signal, the color subcarrier has still to carry a two dimensional signal. Typically the red (R) and the blue (B) information are carried, because the difference signals with luminance (R-Y and B-Y) are stronger than what the difference with green is (G-Y).
SECAM differs from the other color systems by the way the R-Y and B-Y signals are carried.
First, SECAM uses frequency modulation to encode chrominance information on the subcarrier.
Second, instead of transmitting the red and blue information together, it only sends one of them at a time, and uses the information about the other color from the preceding line. It uses a delay line, an analog memory device, for the purpose of storing one line of color information. This justifies the "Sequential, With Memory" name.
Because SECAM transmits only one color at a time, it is free of the color artifacts present in NTSC and PAL and resulting from the combined transmission of both signals.
This means that the vertical colour resolution is halved relative to NTSC. It is however not halved compared to PAL. Although PAL does not eliminate half of vertical color information during encoding, it combines color information from adjacent lines at the decoding stage, in order to compensate for color subcarrier phase errors occurring during the transmission of the Amplitude-Modulated color subcarrier. This is normally done using a delay line borrowed from SECAM (the result is called PAL DL or PAL Delay-Line, sometimes interpreted as DeLuxe), but can be accomplished "visually" in cheap TV sets (PAL standard). Since the FM modulation of SECAM's color subcarrier is insensitive to phase (or amplitude) errors, phase errors do not cause loss of color saturation in SECAM, although they do in PAL. In NTSC such errors cause color shifts.
The colour difference signals in SECAM are actually calculated in the YDbDr colour space, which is a scaled version of the YUV colour space. This encoding is better suitable to the transmission of only one signal at a time.
Because of the FM modulation, SECAM is free of the dot crawl problem commonly encountered with the other analog standards and first widely noticed with the Laserdiscs. Dot crawl can be removed from PAL and NTSC-encoded signals using a comb filter. Such filters are usually only included in high-end displays. Dot crawl patterns (animated checkerboard) are easily visible along vertical lines in DVD menus displayed even by expensive (eg. plasma) displays if these displays are connected to a signal source (DVD player) using a composite PAL or NTSC connection rather than for example RGB.
The idea of reducing the vertical color resolution comes from Henri de France, who observed that color information is approximately identical for two successive lines. Because color information was always supposed to be a cheap and backwards-compatible addition to the monochrome signal, it never had the same horizontal resolution as the monochrome information: the color subcarrier has always a more limited bandwidth than the luminance signal. Therefore, it was not logical to keep the full color resolution vertically either.
DVD and other digital television formats have perpetuated the implementation of this idea, subsampling color both horizontally and vertically. Hence, paradoxically, VHS NTSC videos can have a greater vertical color resolution than DVD.
A similar paradox applies to the vertical resolution in television in general: reducing the bandwidth of the video signal will preserve the vertical resolution, even if the image loses sharpness and is smudged in the horizontal direction. Hence, video could be sharper vertically than horizontally. However, because of the interlacing, vertical resolution is effectively not as great as the number of scan lines. Additionally, transmitting an image with too much vertical detail will cause annoying flicker on television screens, as small details will only appear on a single line, and hence be refreshed at half the frequency. Therefore computer generated text and inserts have to be carefully down-pass filtered to prevent this.
History
Work on SECAM began in 1956. The technology was ready by the end of the fifties, but this was too soon for a wide introduction. Notably, SECAM did not work with the 819-line television standard then used by the then sole French TV network. France had to start the conversion by switching over to a 625-line television standard, which happened at the beginning of the sixties with the introduction of a second network.
SECAM was inaugurated in France on October 1st 1967, on la seconde chaîne (the second network), currently called France 2. A group of four men, all dressed in suits, presumably presenters and network officials, were shown standing in a studio. The image was originally black and white and suddenly switched to color; one of the people said something along "now you can see us as we really are".
The first color television sets costed 5000 Francs. Color TV was not very popular initially; only about 1500 people watched the inaugural program in color. A year later, only 200,000 sets had been sold of an expected million. This pattern was similar to the earlier slow build-up of color television popularity in the USA.
SECAM was later adopted by former French and Belgian colonies, Eastern European countries, the former Soviet Union and Middle Eastern countries. However, with the fall of communism, and following a period when multi-standard TV sets became a commodity, a lot of Eastern European countries decided to switch to PAL.
Why SECAM in France?
Many have argued that the primary motivation for the development of SECAM in France was to protect French television equipment manufacturers. However, incompatibility had started with the earlier decision to uniquely adopt positive video modulation for French broadcast signals. Also, SECAM development predates PAL; and because of frame rate differences (50 versus 60 Hz) and the requirement for compatibility with monochrome TV receivers, it was not possible for Europeans to adopt NTSC. SECAM and PAL addressed the chroma phase problem with NTSC which required the tint control on U.S. sets.
Nonetheless, SECAM was partly developed for reasons of national pride. Henri de France's personal charisma and ambition may have been a contributing factor.
Unlike some other manufacturers, the company where SECAM was invented, Thomson, still sells TV sets worldwide under different brands; this may be due in part to the legacy of SECAM. Thomson bought the company which developed PAL, Telefunken, and today even co-owns the RCA brand — RCA being the creator of NTSC. Thomson also co-authored the current American high-definition TV standard ATSC.
Why SECAM elsewhere?
The adoption of SECAM in Eastern Europe has been attributed to Cold War political machinations: it has been claimed that its use made it impossible for most Eastern Europeans to view television broadcast from outside the Iron Curtain using PAL.
However, remember that PAL and SECAM are just standards for the color subcarrier, used in conjunction with older standards for the base monochrome signals. The names for these monochrome standards are letters, such as M, B/G, D/K, and L. See CCIR, OIRT and FCC (the standardization bodies).
These signals are much more important to compatibility than the color subcarriers. They differ by AM or FM modulation, signal polarisation, relative frequencies within the channel, bandwidth, etc. For example, a PAL D/K TV set will be able to receive a SECAM D/K signal (although in black and white), while it will not be able to receive a PAL B/G signal at all. So even before SECAM came to Eastern European countries, most viewers could not have received Western programs -- and color TV sets were not exactly widespread in the Communist bloc anyway, so the B/W-only reception wasn't actually much of a problem.
Another, speculative political theory is that PAL was originally German, while SECAM came from a country which had better political relations with Eastern Europe after the war.
SECAM varieties
There are three varieties of SECAM:
- French SECAM, used in France and its former colonies
- MESECAM, used in the Middle East
- SECAM D/K, used in the Commonwealth of Independent States and Eastern Europe. (This is simply SECAM used with the D and K monochrome TV transmission standards.)
Around 1983-1984 a new color identification standard has been introduced in order to make more space available inside the signal for adding teletext information (originally according to the Antiope standard). Identification bursts have been made per-line (like in PAL) rather than per-picture. Older SECAM TV sets might not be able to display color for today's broadcasts.
Problems with the standard
Unlike PAL or NTSC, analog SECAM television cannot easily be edited in its native analog form. This is because of the FM modulation SECAM is not linear with respect to the input image, so that electrically mixing two SECAM signals does not yield a valid SECAM signal, unlike with analog PAL or NTSC. For this reason, to mix two SECAM signals, they must be demodulated, have the mix applied to the demodulated signals, and be remodulated again. Hence, post-production is often done in PAL, or in component formats, with the result transcoded into SECAM at the point of transmission. Reducing the costs of running television stations is one reason for some countries' recent switchovers to PAL.
TVs currently sold in SECAM countries support both SECAM and PAL, and more recently baseband NTSC as well (though not usually broadcast NTSC). Although the older analogue camcorders (VHS, VHS-C and 8mm) were produced in SECAM versions, none of the Hi-band models were (S-VHS, S-VHS-C and Hi-8). There are no SECAM Digital camcorders or DVD players. However, this is of dwindling importance: since 1980 most European domestic video equipment uses SCART connectors, allowing the transmission of RGB signals between devices. This eliminates the legacy of PAL, SECAM and NTSC color subcarrier standards.
In general, modern professional equipment is now all-digital, and uses component-based digital interconnects such as CCIR 601 to eliminate the need for any analog processing prior to the final modulation of the analog signal for broadcast. However, large installed bases of analog professional equipment still exist, particularly in third world countries.
Facetious interpretations of the SECAM acronym
American engineers have been known to claim that SECAM stands for "System Essentially Contrary to the American Method". European non-SECAM countries know that it really means "Shows Every Colour All Murky" – a reference to the reduction in vertical colour resolution. Although the first facetious expansion may have reflected the intentions of the SECAM designers, the second one is (as a contrast with PAL) probably a mistake. Given the fact that the French often take a stance against what they call American cultural imperialism, in favor of French culture, SECAM is jokingly said to also stand for "Système Élégant Contre les AMéricains" (Elegant system against the Americans).
Countries which use or have used SECAM
Afghanistan, Andorra, Armenia, Azerbaijan, Belarus, Benin, Bulgaria, Burkina Faso, Burundi, Cambodia (Kampuchea), Central African Republic, Chad, Congo (People's Republic), Côte d'Ivoire, Czech Republic, Djibouti, East Germany, Egypt, Equatorial Guinea, Estonia, France, French Guiana, French Polynesia, Gabon, Georgia, Greece, Guadeloupe, Hungary, Iran, Iraq, Kazakhstan, North Korea, Kyrgyzstan, Latvia, Libya, Lithuania, Luxembourg, Madagascar, Mali, Martinique, Mauritania, Mauritius, Monaco, Mongolia, Morocco, New Caledonia, Niger, North Korea, Poland, Réunion, Romania, Russia, Rwanda, Saint-Pierre and Miquelon, Saudi Arabia, Senegal, Serbia, Slovakia, Syria, Tahiti, Tajikistan, Togo, Tunisia, Turkmenistan, Ukraine, Uzbekistan, Vietnam, Wallis Island, Zaire.
Some SECAM countries are in the process of switching to PAL and are broadcasting in both SECAM and PAL formats. The list does not contain certain countries known to have totally switched to PAL.
See also
External link
de:SECAM fr:Séquentiel couleur avec mémoire ja:SECAM pl:SECAM
